Unitary products group D1EB060 Bedienungsanleitung PDF herunterladen

GENERAL

Model D1EB units are factory assembled cooling only air condi-

tioners designed for outdoor installation on a rooftop or a slab.

Field-installed electric heater accessories are available to provide

electric heat combined with electric cooling. All units and heaters

are certified by AGA and CGA.

The units are completely assembled on rigid, but easily remov-

able base rails. All piping, refrigerant charge, and electrical wir-

ing is factory installed and tested. The units require only electric

power and duct connections at the point of installation.

The electric heaters have nickel-chrome resistance wire ele

ments and utilize single point power connection.

INSPECTION

As soon as a unit isreceived,itshouldbe inspected for possible

damage during transit. If damage is evident, the extent of the

damage should be noted on the carrier's freight bill. Aseparate

request for inspection by the carrier's agent should be made in

writing. Refer to Form 50.15-NM for additional information.

REFERENCE

Additional information on the design, installation, operation

and service of this equipment is available in the following refer-

ence forms:

• 55.70-N1 -General Installation

• 55.70-N2 -Pre-start & Post-start Check List

• 511.26-N1.1V -Electric Heater Accessory

REPLACEMENT PARTS

•

Refer to Replacement Parts Manual for complete listing of

replacement parts on this equipment.

All forms referenced in this instruction may be ordered from:

Standard Register

Norman, OK 73069

Toll Free: Tel. 877-318-9675/Fax. 877-379-7920

Installer should pay particular attention to the words: NOTE, CAUTION and WARNING. Notes are intended to clarify or make

the installation easier. Cautions

are given to prevent equipment damage. Warnings are given to alert installer that personal injury

and/or equipment damage may result if installation procedure is not handled properly.

CAUTION

THE ENCLOSED INSTALLATION INSTRUCTIONS AND ANY APPLICABLE

LOCAL, STATE, AND NATIONAL CODES INCLUDING, BUT NOT LIMITED

TO, BUILDING, ELECTRICAL, AND MECHANICAL CODES.

THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE W ITH

WARNING

OPERATION OF THE PRODUCT COULD CAUSE PERSONAL INJURY

OR PROPERTY DAMAGE.

INCORRECT INSTALLATION MAY CREATE A CONDITION WHERE THE

CHAMPION® SERIES

SINGLE PACKAGE AIR CONDITIONERS

ELECTRIC/ELECTRIC, AIR-COOLED

Supersedes: 035-16703-000-A-0701

035-16703-001-A-0202

INSTALLATION INSTRUCTION



MODELS D1EB018 THRU 060

1-1/2 THRU 5 TON

(10 SEER)

1 2 3 4 5 6 ... 16 17

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTION

GENERALModel D1EB units are factory assembled cooling only air condi-tioners designed for outdoor installation on a rooftop or a slab.Field-installed

Seite 2 - INSTALLATION

10 Unitary Products Group035-16703-001-A-0202FIG. 3 - DIMENSIONS AND CLEARANCESCLEARANCES(Minimum)Front 12"Back 0"Left Side (Filter Access)

Seite 3

CoolingThe following sequences of operation are based on using astandard single-stage cooling thermostat.WITH POWER TO UNIT AND THERMOSTAT IN COOLINGM

Seite 4 - COMPRESSORS

12 Unitary Products Group035-16703-001-A-0202NORMAL MAINTENANCEWARNING:Prior to any of the following maintenance proce-dures, shut off all power to th

Seite 5 - ELECTRICAL DATA (BASIC UNIT)

Unitary Products Group 13035-16703-001-A-0202FIG. 4 - TYPICAL WIRING DIAGRAM (208/230-1-60 POWER SUPPLY) POWER SUPPLY POWER SUPPLY 208/230-1-60 208/23

Seite 6

14 Unitary Products Group035-16703-001-A-0202FIG. 5 - TYPICAL WIRING DIAGRAM (230-3-60 POWER SUPPLY)

Seite 7 - Unitary Products Group 7

Unitary Products Group 15035-16703-001-A-0202L2L1POW ER SUPPLY W /O UTELEC HEAT 460-3-60O R 5 7 5 -3 -6 0USE COPPERCONDUCTORSONLYGNDLU GPOW ER SUPPLY

Seite 8

16 Unitary Products Group035-16703-001-A-0202TYPICAL WIRING DIAGRAM NOTESTYPICAL WIRING DIAGRAM LEGENDHTR 5 ELECTRIC HEATER (OPT. ACCSSRY:

Seite 9

Unitary Products Group5005 York Drive, Norman Oklahoma 73069Subject to change without notice. Printed in U.S.A.Copyright  by York International Co

Seite 10

LIMITATIONSThese units must be installed in accordance with the followingnational and local safety codes.1. National Electrical Code ANSI/NFPS No. 70

Seite 11 - SEQUENCE OF OPERATION

CLEARANCESAll units require certain clearances for proper operation andservice. Refer to Figure 3 for the clearances required for com-bustion, constru

Seite 12 - MAINTENANCE

POWER AND CONTROL WIRINGField wiring to the unit must conform to provisions of the currentN.E.C. ANSI/NFPA No. 70 or C.E.C. and/or local ordinances.Th

Seite 13 - 035-16703-001-A-0202

035-16703-001-A-0202Unitary Products Group 5MODELDEBPOWER SUP-PLYVOLTAGELIMITATIONS1COMPRESSORCOND.FANMOTOR,FLASUPPLYAIRBLOWERMOTOR,FLAMINIMUMCIRCUITA

Seite 14 - 14 Unitary Products Group

035-16703-001-A-02026 Unitary Products GroupDEBPOWERSUPPLYCOMPRESSORCOND.FANMOTORFLASUPPLYAIRBLOWERMOTOR,FLAELECTRIC HEAT ACCESSORYMINIMUMCIRCUITAMPAC

Seite 15 - ELEM ENTARY DIAGRAM

Checking Supply Air CFMTo check the supply air CFM after the initial balancing has beencompleted:1.Remove the two ¼ inch dot plugs in the duct panel.2

Seite 16 - 16 Unitary Products Group

8 Unitary Products Group035-16703-001-A-0202TABLE 7 - SUPERHEAT CHARGING TABLE FOR MODEL D1EB024OUTDOORTEMPERATURE(F)SUPERHEAT AT COMPRESSOR SUCTION (

Seite 17

Unitary Products Group 9035-16703-001-A-0202TABLE 10 - SUPERHEAT CHARGING TABLE FOR MODEL D1EB042OUTDOORTEMPERATURE(F)SUPERHEAT AT COMPRESSOR SUCTION

Kommentare zu diesen Handbüchern

Keine Kommentare

Unitary products group D1EB060 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Wäschetrockner Unitary products group D1EB060 herunter. IO-D1EB018-060,k 1.5-5 ton 10 SEER Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern